SRST configuration CME.

-
Cisco SRST configuration in CME.
Image result for srst cisco


Watch the whole configuration from Here

Highlighted part is related to SRST.

Building configuration...
Current configuration : 2179 bytes
!
! Last configuration change at 09:48:23 UTC Wed Sep 21 2016 by pyramid
version 15.3
service timestamps debug datetime msec
service timestamps log datetime msec
no service password-encryption
!
hostname Router
!
boot-start-marker
boot-end-marker
!
aqm-register-fnf
!
enable password pyramid
!
no aaa new-model
!
!
!
!
!
!
!
ip cef
no ipv6 cef
multilink bundle-name authenticated
!
!
!
!
!
!
!
voice-card 0
!
!
!
voice service voip
 allow-connections h323 to h323
 allow-connections h323 to sip
 allow-connections sip to h323
 allow-connections sip to sip
 fax protocol t38 version 0 ls-redundancy 0 hs-redundancy 0 fallback none
 sip
  registrar server expires max 600 min 60
!
!
voice register global
 mode srst
 system message Fallback active
 max-dn 20
 max-pool 20
 authenticate realm cisco.com
 timezone 39
 application sip.app
!
voice register pool  1
 id network 192.168.0.0 mask 255.255.255.0
 proxy 192.168.0.234 monitor probe icmp-ping
 codec g711ulaw
 no vad
!
!
!
!
!
!
application
 global
  service alternate default
 !
!
license udi pid CISCO2901/K9 sn FGL1927239Q
license boot module c2900 technology-package uck9
hw-module pvdm 0/0
!
hw-module pvdm 0/1
!
!
!
username pyramid password 0 pyramid
!
redundancy
!
!
!
!
!
!
interface Embedded-Service-Engine0/0
 no ip address
 shutdown
!
interface GigabitEthernet0/0
 ip address 192.168.0.199 255.255.255.0
 duplex auto
 speed auto
!
interface GigabitEthernet0/1
 no ip address
 shutdown
 duplex auto
 speed auto
!
ip forward-protocol nd
!
no ip http server
no ip http secure-server
!
!
!
!
!
control-plane
!
!
voice-port 0/0/0
!
voice-port 0/0/1
!
voice-port 0/0/2
!
voice-port 0/0/3
 !
 !
 !
 !
!
!
mgcp behavior rsip-range tgcp-only
mgcp behavior comedia-role none
mgcp behavior comedia-check-media-src disable
mgcp behavior comedia-sdp-force disable
!
mgcp profile default
!
!
!
sip-ua
 registrar ipv4:192.168.0.199 expires 600
!
!
!
gatekeeper
 shutdown
!
!
!
line con 0
line aux 0
line 2
 no activation-character
 no exec
 transport preferred none
 transport output pad telnet rlogin lapb-ta mop udptn v120 ssh
 stopbits 1
line vty 0 4
 login local
 transport input all
!
scheduler allocate 20000 1000
!
end

Popular posts from this blog

Converting cisco 1852 AP to controller (Mobility express)

-
           CONVERTING 1852 AP TO MOBILITY EXPRESS Get your work done easily, watch the video for this process:   CLICK HERE FOR VIDEO Pre requisites: 1.1852 AP 2.Mobilty express image 3.Mobility express update image 4.TFTP server 5.DHCP server Procedure: Step-1: Connect the 1852 AP in network which have DHCP server. Your PC should be in same network and reachability should be there. (between PC and AP) Step-2: Install the ME image  Open the tftp server and start it. Keep the Mobility express image (30MB) in TFTP-Root directory. go to AP console and issue the below commands: logging console disable      //optional prevents from bothering up with console logging messages debug capwap console cli ap-type mobility-express tftp://x.x.x.x/<image>.tar With the above commands, We have downloaded the ME image into the AP. It Will automatically reboots waits until it does!  Wait 10 - 15 M...
Read more

Cisco Access Point Cap to Sap / Sap to Cap conversion

-
Image
CONVERTING CISCO CAP TO SAP / SAP TO CAP (lwap - Ap / Ap - Lwap): You can watch the video too...!!! Conversion of the AP's using downgrade or upgrade takes a lot of time and most of the times the IOS loaded will lead to an error, So Instead of that process i am going to use ROMMON recovery, It's a simple procedure for IOS changing. It will help a Network engineer's work a lot easier. ROMMON recovery is a process of Deleting the existing flash, and re-inserting our desired IOS. Follow the below  procedure. Mandatory Pre requirements: A PC with TFTP server installed. (Turn off Antivirus, Firewall in PC) Cisco AP which is to be converted. Console cable  Procedure: 1) Login to the CLI go to "privilege mode" . (Enable mode) 2) Execute the below command:      show flash: Output for the above command will be like this In the above output following are the firmware images: ap3g2-k9w8-tar.153-3.JBB5.tar ap3g2-k9w8-mx.152-2.JB2  We need to de...
Read more

HP Switch Comware firmware Upgradation

-
Image
      UPGRADING FIRMWARE IN HP SWITCHES In Switch: <system>system-view [system]ftp server enable local-user admin password simple admin authentication-attribute user-role network-admin service-type ftp quit vlan 2 port gigabitethernet 1/0/1 quit interface vlan-interface 2 ip address 192.168.1.1 255.255.255.0 quit save in PC Turn off windows firewall Turn off Any antivirus Turn off windows defender //connect a cable one end to switch 1/0/1 port and other end to your PC. configure static ip address in your PC. IP:192.168.1.10 Mask: 255.255.255.0 Test the connectivity by pinging 192.168.1.1 Open command prompt with administrator rights Type: ftp 192.168.1.1 username: admin password: admin ftp> binary ftp> put filename.ipe wait for 3 min. file will be uploaded to switch. after uploading completed type in the following commands. <system>boot-loader file flash:filename.ipe all main pres...
Read more